 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1 1 1 1 1 k8upgrade-vm800 user manual version 1.0 published april 2005 copyright?2005 asrock inc. all rights reserved.
2 2 2 2 2 copyright notice: copyright notice: copyright notice: copyright notice: copyright notice: no part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of asrock inc. products and corporate names appearing in this manual may or may not be regis- tered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners? benefit, without intent to infringe. disclaimer: disclaimer: disclaimer: disclaimer: disclaimer: specifications and information contained in this manual are furnished for informa- tional use only and subject to change without notice, and should not be constructed as a commitment by asrock. asrock assumes no responsibility for any errors or omissions that may appear in this manual. with respect to the contents of this manual, asrock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warran- ties or conditions of merchantability or fitness for a particular purpose. in no event shall asrock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if asrock has been advised of the possibility of such damages arising from any defect or error in the manual or product. this device complies with part 15 of the fcc rules. operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. asrock website: http://www.a srock.com 3 3 3 3 3 contents contents contents contents contents 1. 1. 1. 1. 1. introduction introduction introduction introduction introduction ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ 5 5 5 5 5 1.1 package contents ..................................................................... 5 1.2 specifications ........................................................................... 6 1.3 motherboard layout ................................................................. 8 1.4 asrock i/o plus tm .................................................................... 9 2. 2. 2. 2. 2. installation installation installation installation installation .............................................................. .............................................................. .............................................................. .............................................................. .............................................................. 10 10 10 10 10 pre-installation precautions ............................................................... 10 2.1 cpu installation ......................................................................... 11 2.2 installation of cpu fan and heatsink ....................................... 11 2.3 installation of memory modules (dimm) .................................... 12 2.4 expansion slots (future cpu port, pci, agp, and amr slots) ....... 13 2.5 jumpers setup .......................................................................... 15 2.6 onboard headers and connectors .......................................... 16 2.7 serial ata (sata) hard disks in stallation ................................ 19 2.8 hot plug function for sata hdds ............................................ 19 2.9 installing windows 2000 / windows xp / windows xp 64-bit with raid functions ................................................................. 20 2.9.1 installing windows 2000 / windows xp with raid functions ........................................................................ 20 2.9.2 installing windows xp 64-bit with raid functions ....... 20 2.10 installing windows 98 / me / 2000 / xp / xp 64-bit without raid functions .................................................................................. 21 3. 3. 3. 3. 3. bios s bios s bios s bios s bios s etup utility etup utility etup utility etup utility etup utility ................................................... ................................................... ................................................... ................................................... ................................................... 22 22 22 22 22 3.1 introduction ............................................................................... 22 3.1.1 bios menu bar ............................................................... 22 3.1.2 navigation keys ............................................................. 23 3.2 main screen .............................................................................. 23 3.3 advanced screen .................................................................... 24 3.3.1 cpu configuration .......................................................... 25 3.3.2 chipset configuration ..................................................... 27 3.3.3 acpi configuration ......................................................... 29 3.3.4 ide configuration ............................................................ 30 3.3.5 pcipnp configuration ...................................................... 32 3.3.6 floppy configuration ...................................................... 32 3.3.7 super io configuration ................................................... 33 3.3.8 usb configuration .......................................................... 34 3.4 hardware health event monitoring screen ............................. 35 3.5 boot screen .............................................................................. 35 3.5.1 boot settings configuration ........................................... 36 4 4 4 4 4 3.6 security screen ........................................................................ 36 3.7 exit screen ............................................................................... 37 4. 4. 4. 4. 4. software support software support software support software support software support ................................................... ................................................... ................................................... ................................................... ................................................... 38 38 38 38 38 4.1 install operating system ........................................................... 38 4.2 support cd information ............................................................. 38 4.2.1 running support cd ....................................................... 38 4.2.2 drivers menu .................................................................. 38 4.2.3 utilities menu ................................................................... 38 4.2.4 contact inf ormation ........................................................ 38 appendix: amd?s cool ?n? quiet appendix: amd?s cool ?n? quiet appendix: amd?s cool ?n? quiet appendix: amd?s cool ?n? quiet appendix: amd?s cool ?n? quiet tm tm tm tm tm t t t t t echnology echnology echnology echnology echnology ...... ...... ...... ...... ...... 39 39 39 39 39 5 5 5 5 5 1. 1. 1. 1. 1. introduction introduction introduction introduction introduction thank you for purchasing asrock k8upgrade-vm800 motherboard, a reliable motherboard produced under asrock?s consistently stringent quality control. it de- livers excellent performance with robust design conforming to asrock?s commit- ment to quality and endurance. in this manual, chapter 1 and 2 contain introduction of the motherboard and step-by- step guide to the hardware installation. chapter 3 and 4 contain the configuration guide to bios setup and information of the support cd. because the motherboard specifications and the bios software might be updated, the content of this manual will be subject to change without notice. in case any modifications of this manual occur, the updated version will be available on asrock website without further notice. you may find the latest memory and cpu support lists on asrock website as well. asrock website http://www .a srock.com 1.1 1.1 1.1 1.1 1.1 package contents package contents package contents package contents package contents 1 x asrock k8upgrade-vm800 motherboard (micro atx form factor: 9.0-in x 9.6-in, 22.9 cm x 24.4 cm) 1 x asrock k8upgrade-vm800 quick installation guide 1 x asrock k8upgrade-vm800 support cd 1 x ultra ata 66/100/133 ide ribbon cable (80-conductor) 1 x 3.5-in floppy drive ribbon cable 1 x serial ata (sata) data cable (optional) 1 x serial ata (sata) hdd power cable (optional) 1 x asrock i/o plus tm shield 1 x com port bracket 1 x asrock mr card (optional) 6 6 6 6 6 1.2 1.2 1.2 1.2 1.2 specifications specifications specifications specifications specifications platform: micro atx form factor: 9.0-in x 9.6-in, 22.9 cm x 24.4 cm cpu: 754-pin socket supporting advanced 64-bit amd athlon tm 64 and 32-bit sempron processor supports amd?s cool ?n? quiet tm technology (see caution 1 ) chipsets: north bridge: via k8m800 chipset fsb @ 800 mhz / 1.6 gt/s south bridge: via vt8237r chipset supports usb 2.0, ata 133, sata 1.5gb/s memory: 2 x ddr dimm slots: ddr1 and ddr2 support pc3200 (ddr400) / pc2700 (ddr333) / pc2100 (ddr266), max. 2gb ide: ide1: ata 133 / ultra dma mode 6 ide2: ata 133 / ultra dma mode 6 supports up to 4 ide devices serial ata: 2 x sata connectors supports up to 2 sata devices at 1.5gb/s data transfer rate floppy port: supports up to 2 floppy disk drives audio: 5.1 channels ac?97 audio onboard vga: intergrated unichrome pro 3d/2d graphics controller , supports directx 8.1 lan: speed: 802.3u (10/100 ethernet), supports wake-on-lan hardware monitor: cpu temperature sensing motherboard temperature sensing cpu overheat shutdown to protect cpu life (asrock u-cop)(see caution 2 ) cpu fan tachometer chassis fan tachometer voltage monitoring: +12v, +5v, +3.3v, vcore future cpu port: supports cpu upgrade from amd 754-pin cpu to amd 939-pin cpu (see page 13 for details) pci slots: 2 x pci slots, pci specification 2.2 agp slot: 1 x agp slot supports 1.5v, 8x / 4x agp card (see caution 3 ) amr slot: 1 slot, supports asrock mr card (optional) usb 2.0: 8 usb 2.0 ports: 6 ready-to-use usb 2.0 ports on the i/o panel plus 2 on-board headers supporting 2 extra usb 2.0 ports (see caution 4 ) 7 7 7 7 7 asrock i/o plus tm : 1 ps/2 mouse port, 1 ps/2 keyboard port 1 vga port 1 parallel port (ecp/epp support) 6 ready-to-use usb 2.0 ports 1 rj-45 port audio jack: line in / line out / microphone com port: 1 com port header to support a com port module bios: ami legal bios supports ?plug and play? acpi 2.0 compliance wake up events smbios 2.3.1 support cpu frequency stepless control (only for advanced users? reference, see caution 5 ) os: microsoft ? windows ? 98 se / me / 2000 / xp compliant caution! 1. for power-saving sake, it is strongly recommended to enable amd?s cool ?n? quiet tm technology under windows system. see appendix on page 39 to enable amd?s cool ?n? quiet tm technology. 2. while cpu overheat is detected, the system will automatically shutdown. before you resume the system, please check if the cpu fan on the motherboard functions properly and unplug the power cord, then plug it back again. to improve heat dissipation, remember to spray thermal grease between the cpu and the heatsink when you install the pc system. 3. do not use a 3.3v agp card on the agp slot of this motherboard! it may cause permanent damage! 4. power management for usb 2.0 works fine under microsoft ? windows ? xp sp1 / 2000 sp4. it may not work properly under microsoft ? windows ? 98/ me. 5. although this motherboard offers stepless control, it is not recommended to perform over-clocking. frequencies other than the recommended cpu bus frequencies may cause the instability of the system or damage the cpu. 8 8 8 8 8 1.3 motherboard layout 1.3 motherboard layout 1.3 motherboard layout 1.3 motherboard layout 1.3 motherboard layout socket 7 54 ddr2 (64/72 bit, 184-pin module) ddr1 (64/72 bit, 184-pin module) atxpwr1 ide1 ide2 floppy1 cpu_fan1 ps2_usb_pw1 1 atx12v1 via vt8237r chipset pci 1 pci 2 1.5v_agp1 future_cpu_port1 via k8m800 chipset cmos battery sata1 sata2 clrcmos2 1 cha_fan1 usb67 1 speaker1 1 ir1 1 hdled reset pled pwrbtn 1 panel 1 game1 1 amr1 4mb bios super i/o lan phy audio codec audio1 jr1 jl1 1 usb45 cd1 aux1 1 parallel port vga1 ps2 mouse ps2 keyboard usb 2.0 t: usb2 b: usb3 usb 2.0 t: usb0 b: usb1 top: rj-45 shared usb 2.0 t: usb4 b: usb5 top: line in center: line out bottom: mic in ddr400 ata133 agp 8x usb2.0 fsb800 sata 5.1ch k8upgrade-vm800 1 j15 j9 j10 j7 1 j8 1 j5 1 j6 1 j3 1 j4 1 j1 1 j2 1 1 1 com1 1 24.4cm (9.6-in) 22.9cm (9.0-in) 1 2 4 3 16 19 17 18 57 8 9 11 13 14 15 12 10 6 20 21 22 23 24 25 26 32 33 30 27 29 28 31 34 8 1 ps2_usb_pwr1 jumper 18 system panel header (p anel1) 2 atx 12v power connector (atx12v1) 19 game port header (game1) 3 cpu fan connector (cpu_fan1) 20 chassis speaker header (speaker 1) 4 754-pin cpu socket 21 usb 2.0 header (usb67, blue) 5 cpu heatsink retention module 22 chassis fan connector (cha_fan1) 6 north bridge controller 23 clear cmos jumper (clrcmos2) 7 184-pin ddr dimm slots (ddr1- 2) 24 agp slot (1.5v_agp1) 8 j9 / j10 / j15 jumpers 25 com port header (com1) 9 infrared module header (ir1) 26 amr slot (amr1) 10 flash memory 27 pci s lots (pci1- 2) 11 atx power conne ctor (atxpwr1) 28 jr1 / jl1 jumpers 12 floppy connector (floppy1) 29 front panel audio header (audio1) 13 primary ide connector (ide1, blue) 30 future cpu port (future_cpu_port1) 14 secondary ide connector (ide2, black) 31 internal audio connector: aux1 (white) 15 south bridge controller 32 internal audio connector: cd1 (black) 16 primary serial ata connector (sata1) 33 shared usb 2.0 header (usb45, blue) 17 secondary serial ata connector (sata2) 34 j1 - j8 jumpers 9 9 9 9 9 1.4 asrock i/o plus 1.4 asrock i/o plus 1.4 asrock i/o plus 1.4 asrock i/o plus 1.4 asrock i/o plus tm tm tm tm tm 1 parallel port 7 usb 2.0 ports (usb01) 2 rj-45 port 8 usb 2.0 ports (usb23) 3 line in (light blue) 9 vga port 4 line out (lime) 10 ps/2 keyboard port (purple) 5 microphone (pink) 11 ps/2 mouse port (green) 6 shared usb 2.0 ports (usb45) 1 2 3 4 5 6 7 8 9 1 0 11 10 10 10 10 10 2. 2. 2. 2. 2. installation installation installation installation installation k8upgarde-vm800 is a micro atx form factor (9.0-in x 9.6-in, 22.9 cm x 24.4 cm) motherboard. before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. pre-installation precautions pre-installation precautions pre-installation precautions pre-installation precautions pre-installation precautions take note of the following precautions before you install motherboard components or change any motherboard settings. before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. failure to do so may cause severe damage to the motherboard, peripherals, and/or components. 1. unplug the power cord from the wall socket before touching any component. 2. to avoid damaging the motherboard components due to static electricity, never place your motherboard directly on the carpet or the like. also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. 3. hold components by the edges and do not touch the ics. 4. whenever you uninstall any component, place it on a grounded anti- static pad or in the bag that comes with the component. 5. when placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! doing so may damage the motherboard. 11 11 11 11 11 2.1 2.1 2.1 2.1 2.1 cpu installation cpu installation cpu installation cpu installation cpu installation step 1. unlock the socket by lifting the lever up to a 90 o angle. step 2. position the cpu directly above the socket such that the cpu corner with the golden triangle matches the socket corner with a small triangle. step 3. carefully insert the cpu into the socket until it fits in place. the cpu fits only in one correct orientation. do not force the cpu into the socket to avoid bending of the pins. step 4. when the cpu is in place, press it firmly on the socket while you push down the socket lever to secure the cpu. the lever clicks on the side tab to indicate that it is locked. 2.2 2.2 2.2 2.2 2.2 installation of cpu fan and heatsink installation of cpu fan and heatsink installation of cpu fan and heatsink installation of cpu fan and heatsink installation of cpu fan and heatsink after you install the cpu into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. you also need to spray thermal grease between the cpu and the heatsink to improve heat dissipation. make sure that the cpu and the heatsink are securely fas- tened and in good contact with each other. then connect the cpu fan to the cpu fan connector (cpu_fan1, see page 8, no. 3). for proper installation, please kindly refer to the instruction manuals of the cpu fan and the heatsink. step 1: lift up the socket lever step 2 / step 3: match the cpu golden triangle to the socket corner step 4: push down and lock the socket lever lever 90 up cpu golden triangle socket corner 12 12 12 12 12 notch brea k notch brea k 2.3 2.3 2.3 2.3 2.3 installation of memory modules (dimm) installation of memory modules (dimm) installation of memory modules (dimm) installation of memory modules (dimm) installation of memory modules (dimm) this motherboard is equipped with two 184-pin ddr (double data rate) dimm slots. please make sure to disconnect power supply before adding or removing dimms or the system components. step 1. unlock a dimm slot by pressing the retaining clips outward. step 2. align a dimm on the slot such that the notch on the dimm matches the break on the slot. the dimm only fits in one correct orientation. it will cause permanent damage to the motherboard and the dimm if you force the dimm into the slot at incorrect orientation. step 3. firmly insert the dimm into the slot until the retaining clips at both ends fully snap back in place and the dimm is properly seated. 13 13 13 13 13 2.4 2.4 2.4 2.4 2.4 expansion slots expansion slots expansion slots expansion slots expansion slots (future cpu port, pci slots, agp slot, and amr slots) (future cpu port, pci slots, agp slot, and amr slots) (future cpu port, pci slots, agp slot, and amr slots) (future cpu port, pci slots, agp slot, and amr slots) (future cpu port, pci slots, agp slot, and amr slots) there are 1 future cpu port, 2 pci slots, 1 agp slot and 1 amr slot on k8upgrade- vm800 motherboard. future cpu port (yellow-colored port): future cpu port allows you to upgrade your amd 754-pin cpu to amd 939-pin cpu by installing an add-on asrock 939cpu board into this future cpu port on k8upgrade- vm800 motherboard. before you upgrade the 754-pin cpu to the 939-pin cpu, it is necessary to adjust the jumper settings for those required jumpers on k8upgrade- vm800 motherboard. please refer to the table below for the correct jumper settings. this yellow-colored future cpu port is not an agp slot! please do not insert any agp card into it! cpu type jumper settings 939-pin cpu (using add-on asrock 939cpu board ) 754-pin cpu (default) 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 1_ 2 1_ 2 j1 j2 j3 j4 j5 j6 j7 j8 1_ 2 2 _ 3 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 2 _ 3 2 _ 3 j1 j2 j3 j4 j5 j6 j7 j8 j15 j15 j9 j10 j9 j10 14 14 14 14 14 note when adjusting the jumper settings, you may use the tool, jumper cap remover, to help you removing the jumper caps more easily. this jumper cap remover is bundled in your motherboard package, and please follow the ?jumper cap remover instruction? to use it properly. pci slots: pci slots are used to install expansion cards that have the 32-bit pci interface. agp slot: the agp slot is used to install a graphics card. the asrock agp slot has a special design of clasp that can securely fasten the inserted graphics card. please do not use a 3.3v agp card on the agp slot of this motherboard! it may cause permanent damage! for the voltage infor- mation of your agp card, please check with the agp card vendors. amr slot: amr slot is used to insert an asrock mr card (optional) with v.92 modem functionality. installing an expansion card installing an expansion card installing an expansion card installing an expansion card installing an expansion card step 1. bef ore installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. step 2. remove the system unit cover (if your motherboard is already installed in a chassis). step 3. re move the bracket facing the slot that you intend to use. keep the screws for later use. step 4. align the card connector with the slot and press firmly until the card is completely seated on the slot. step 5. fa sten the card to the chassis with screws. step 6. replace the system cover. 15 15 15 15 15 + 5v 1 _ 2 + 5vsb 2 _ 3 jr 1 jl 1 2.5 2.5 2.5 2.5 2.5 jumpers setup jumpers setup jumpers setup jumpers setup jumpers setup the illustration shows how jumpers are setup. when the jumper cap is placed on pins, the jumper is ?short?. if no jumper cap is placed on pins, the jumper is ?open?. the illustration shows a 3-pin jumper whose pin1 and pin2 are ?short? when jumper cap is placed on these 2 pins. jumper setting ps2_usb_pwr1 short pin2, pin3 to enable (see p.8, no. 1) +5vsb (standby) for ps/2 or usb wake up events. note: to select +5vsb, it requires 2 amp and higher standby current provided by power supply. jr1 / jl1 jumper (see p.8, no. 28) note: if the jumpers jl1 and jr1 are short, both the front panel and the rear panel audio connectors can work. clear cmos jumper (clrcmos2) (see p.8, no. 23) note: clrcmos2 allows you to clear the data in cmos. the data in cmos includes system setup information such as system password, date, time, and system setup parameters. to clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. after waiting for 15 seconds, use a jumper cap to short the clear cmos jumper for 5 seconds. after shorting the clear cmos jumper, please remove the jumper cap. however, please do not clear the cmos right after you update the bios. if you need to clear the cmos when you just finish updating the bios, you must boot up the system first, and then shut it down before you do the clear-cmos action. 16 16 16 16 16 2.6 onboard headers and connectors 2.6 onboard headers and connectors 2.6 onboard headers and connectors 2.6 onboard headers and connectors 2.6 onboard headers and connectors onboard headers and connectors are not jumpers. do not place jumper caps over these headers and connectors. placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! ? floppy connector (33-pin floppy1) (see p.8 no. 12) note: make sure the red-striped side of the cable is plugged into pin1 side of the connector. primary ide connector (blue) secondary ide connector (black) (39-pin ide1, see p.8 no. 13) (39-pin ide2, see p.8 no. 14) note: if you use only one ide device on this motherboard, please set the ide device as ?master?. please refer to the instruction of your ide device vendor for the details. besides, to optimize compatibility and performance, please connect your hard disk drive to the primary ide connector (ide1, blue) and cd-rom to the secondary ide connector (ide2, black). serial ata connectors these two serial ata (sata) (sata1: see p.8 no. 16) connectors support sata data (sata2: see p.8 no. 17) cables for internal storage devices. the current sata interface allows up to 1.5 gb/s data transfer rate. serial ata (sata) either end of the sata data cable data cable can be connected to the sata hard disk or the sata connector on the motherboard. f l oppy1 pin1 ide1 pin1 ide 2 pin1 the red-striped side to pin1 connect the black end to the ide devices connect the blue end to the motherboard 80-conductor ata 66/100/133 cable sata2 sata1 17 17 17 17 17 serial ata (sata) please connect the black end of power cable sata power cable to the power (optional) connector on each drive. then connect the white end of sata power cable to the power connector of the power supply. usb 2.0 header asrock i/o plus tm accommo- (9-pin usb67) dates 6 default usb 2.0 ports. if (see p.8 no. 21) those usb 2.0 ports on the i/o panel are not sufficient, this usb 2.0 header is available to support 2 additional usb 2.0 ports. shared usb 2.0 header this usb45 header is shared (9-pin usb45) with the usb 2.0 ports 4,5 on (see p.8 no. 33) asrock i/o plus tm . when using the front panel usb ports by attaching the front panel usb cable to this header (usb45), the usb ports 4,5 on asrock i/o plus tm will not be able to function. infrared module header this header supports an (5-pin ir1) optional wireless transmitting (see p.8 no. 9) and receiving infrared module. internal audio connectors these connectors allow you (4-pin cd1, 4-pin aux1) to receive stereo audio input (cd1: see p.8 no. 32) from sound sources such as (aux1: see p.8 no. 31) a cd-rom, dvd-rom, tv tuner card, or mpeg card. front panel audio header this is an interface for front (9-pin audio1) panel audio cable that allows (see p.8 no. 29) convenient connection and control of audio devices. gnd gnd + 5 va backout-r backout-l aud-out-l aud-out-r mic- p ower mic 1 dummy gnd + 5 v irtx irrx 1 usb_ p wr usb_ p wr p + 6 p - 6 p +7 p -7 gnd gnd dummy 1 usb_ p wr usb_ p wr p + 5 p - 5 p +4 p -4 gnd gnd dummy 1 connect to the sata hdd power connector connect to the power supply cd-r gnd gnd cd-l aux-r gnd gnd aux-l cd1 aux1 18 18 18 18 18 system panel header this header accommodates (9-pin panel1) several system front panel (see p.8 no. 18) functions. chassis speaker header please connect the chassis (4-pin speaker 1) speaker to this header. (see p.8 no. 20) chassis fan connector please connect a chassis fan (3-pin cha_fan1) cable to this connector and (see p.8 no. 22) match the black wire to the ground pin. cpu fan connector ple ase connect the cpu fan (3-pin cpu_fan1) cable to this connector and (see p.8 no. 3) match the black wire to the ground pin. atx power connector please connect an atx power (20-pin a txpwr1) supply to this connector. (see p.8 no. 11) com port header this com port header is used (9-pin com1) to support a com port module. (see p.8 no. 25) atx 12v power connector please note that it is necessary (4-pin atx12v1) to connect a power supply with (see p.8 no. 2) atx 12v plug to this connector. failing to do so will cause power up failure. g n d +12v c ha_fan_ s pee d +5v du mmy du mmy s peake r 1 g n d pw rb tn# ple d - ple d + du mmy r e s et# g n d h d le d + h d le d - 1 ccts#1 ddsr#1 ddtr#1 rrxd1 ddcd#1 ttxd1 gnd rrts#1 rri#1 1 c p u _fan_ s pee d g n d +12v 19 19 19 19 19 game port hea der connect a game cable to this (15-pin game1) header if the game port bracket (see p.8 no. 19) is installed. 2.7 2.7 2.7 2.7 2.7 serial a serial a serial a serial a serial a t t t t t a (sa a (sa a (sa a (sa a (sa t t t t t a) hard disks installation a) hard disks installation a) hard disks installation a) hard disks installation a) hard disks installation this motherboard supports serial ata (sata) hard disks and raid functions. this section will guide you to install the sata hard disks. step 1: in stall the sata hard disks into the drive bays of your chassis. step 2: connect the sata power cable to the sata hard disk. step 3: connect one end of the sata data cable to the motherboard?s sata connector. step 4: connect the other end of the sata data cable to the sata hard disk. 2.8 2.8 2.8 2.8 2.8 hot plug f hot plug f hot plug f hot plug f hot plug f unction for sa unction for sa unction for sa unction for sa unction for sa t t t t t a hdds a hdds a hdds a hdds a hdds k8upgrade-vm800 motherboard supports hot plug function for sata devices. what is hot plug function? if the sata hdds are not set for raid configuration, it is called ?hot plug? for the action to insert and remove the sata hdds while the system is still power-on and in working condition. however, please note that it cannot perform hot plug if the os has been installed into the sata hdd. warning! although this motherboard supports hot plug function for sata devices, there are still some limitation. please ensure to read the instruction in the support cd before you use hot plug function. failure to do so may lose the data in the sata hdds or damage the sata hdds. for the detailed instruction, please refer to the document in the support cd at the following path: ..\ raid bios setting utility mi d i_ ou t ja b 2 j b y j bb 2 mi d i_in +5v jay g n d g n d 1 jax ja b 1 +5v j b x j bb 1 +5v 20 20 20 20 20 2.9 2.9 2.9 2.9 2.9 installing windows 2000 / windows xp / installing windows 2000 / windows xp / installing windows 2000 / windows xp / installing windows 2000 / windows xp / installing windows 2000 / windows xp / windows xp 64-bit with raid functions windows xp 64-bit with raid functions windows xp 64-bit with raid functions windows xp 64-bit with raid functions windows xp 64-bit with raid functions if you want to install windows 2000 / windows xp / windows xp-64bit os on your system with raid functions, please refer to the below methods for proper installation according to the different windows os versions. 2.9.1 2.9.1 2.9.1 2.9.1 2.9.1 installing windows 2000 / windows xp with installing windows 2000 / windows xp with installing windows 2000 / windows xp with installing windows 2000 / windows xp with installing windows 2000 / windows xp with raid functions raid functions raid functions raid functions raid functions if you want to install windows 2000 / windows xp os on your sata hdds with raid functions, please follow the below steps. step 1: make a sata driver diskette. a. insert the asrock support cd into your optical drive to boot your system. b. during post at the beginning of system boot-up, press 21 21 21 21 21 step 1: make a sata driver diskette. a. insert the floppy diskette into your floppy drive. b. copy the sata 64-bit drivers to your floppy diskette. the sata 64-bit drivers are located at the following path in the support cd: .. \ 64bit sata driver step 2: install windows xp 64-bit os on your system. after making a sata driver diskette, you can start to install windows xp 64- bit on your system. after the installation of windows 2000 / windows xp / windows xp 64-bit os, if you want to manage raid functions, you are allowed to use both ?sata raid bios? and ?via raid tool? for raid configuration. please refer to the document in the support cd, ?guide to sata hard disks installation and raid configuration?, which is located in the folder at the following path: .. \ sata raid bios and the document in the support cd, ?guide to via raid tool?, which is located in the folder at the following path: .. \ via raid tool 1. windows 98 / windows me does not support raid functions. 2. if you want to use ?via raid tool? in windows environment, please install sata drivers from the support cd again so that ?via raid tool? will be installed to your system as well. 2.10 2.10 2.10 2.10 2.10 installing windows 98 / me / 2000 / xp / xp 64-bit installing windows 98 / me / 2000 / xp / xp 64-bit installing windows 98 / me / 2000 / xp / xp 64-bit installing windows 98 / me / 2000 / xp / xp 64-bit installing windows 98 / me / 2000 / xp / xp 64-bit without raid functions without raid functions without raid functions without raid functions without raid functions if you want to install windows 98 / me / 2000 / xp / xp 64-bit on your sata hdds without raid functions or you want to install windows 98 / me / 2000 / xp / xp 64-bit on your ide hdds instead of sata hdds, please follow the below steps. step 1: set up bios. a. enter bios setup utility ? advanced screen ? ide configuration. b. set the ?sata operation mode? option from [raid] to [non-raid]. step 2: install windows 98 / me / 2000 / xp / xp 64-bit os on your system. after setting up bios, you can start to install windows 98 / me / 2000 / xp / xp 64-bit on your system. if you don?t want to set up raid functions, there is no need to make a sata driver diskette. if you want to install windows 98 / windows me on your sata hdds without raid functions, you don?t have to set up bios. please install windows 98 / windows me os on your system directly. 22 22 22 22 22 3. 3. 3. 3. 3. bios setup utility bios setup utility bios setup utility bios setup utility bios setup utility 3.1 introduction 3.1 introduction 3.1 introduction 3.1 introduction 3.1 introduction this section explains how to use the bios setup utility to configure your system. the flash memory on the motherboard stores the bios setup utility. you may run the bios setup utility when you start up the computer. please press 23 23 23 23 23 3.1.2 3.1.2 3.1.2 3.1.2 3.1.2 navigation keys navigation keys navigation keys navigation keys navigation keys please check the following table f or the function description of each navigation key. navigation key(s) function description / moves cursor left or right to select screens / moves cursor up or down to select items + / - to change option for the selected items 24 24 24 24 24 if asrock 939cpu board is installed into the future_cpu_port on this motherboard, you will see the below main screen when entering the bios setup utility. 3.3 3.3 3.3 3.3 3.3 advanced screen advanced screen advanced screen advanced screen advanced screen in this section, you may set the configurations for the following items: cpu configuration, chipset configuration, acpi configuration, ide configuration, pcipnp configuration, floppy configuration, superio configuration, and usb configuration. setting wrong values in this section may cause the system to malfunction. bios setup utility main advanced h/w monitor boot security exit system overview system time system date [ :00:09] [mon 11/08/2004] use [enter], [tab] or [shift-tab] to select a field. use [+] or [-] to configure system time. select screen select item +- change field tab select field f1 general help f9 load defaults f10 save and exit esc exit bios version processor type processor speed l1 cache size l2 cache size total memory ddr 1 (k8_939) ddr 2 (k8_939) ddr 3 (k8_939) ddr 4 (k8_939) : k8upgrade-vm800 bios p1.0 : amd athlon(tm) 64 processor 3400+ : 2200 mhz : 128kb : 1024kb :512mbwith64mbsharedmemory single channel memory mode : 512mb/133mhz (ddr266) : none : none : none v02.54 (c) copyright 1985-2003, american megatrends, inc. 17 bios setup utility main h/w monitor boot security exit advanced settings warning : setting wrong values in below sections may cause system to malfunction. configure cpu select screen select item enter go to sub screen f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced cpu configuration chipset configuration ide configuration pcipnp configuration floppy configuration superio configuration usb configuration acpi configuration 25 25 25 25 25 cpu host frequency while entering setup, bios auto detects the present cpu host frequency of this motherboard. the actual cpu host frequency will show in the following item. spread spectrum this item should always be [disabled] for better system stability. cool ?n? quiet use this item to enable or disable amd?s cool ?n? quiet tm technology. processor maximum multiplier it will display processor maximum multiplier for reference. processor maximum voltage it will display processor maximum voltage for reference. multiplier/voltage change this item is set to [auto] by default. if it is set to [manual], you may adjust the value of processor multiplier and processor voltage. however, it is recom- mended to keep the default value for system stability. bios setup utility cpu configuration select how to set the cpu host frequency. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit actual frequency (mhz) cpu host frequency [200] [auto] spread spectrum cool'n'quiet [auto] [disabled] processor maximum multiplier processor maximum voltage multiplier/voltage change memory clock flexibility option bank interleaving burst length cas latency (cl) trcd tras trp ma timing [auto] [auto] [auto] [4 beats] [auto] [auto] [auto] [auto] [2t] [disabled] x11 1.550 v 3.3.1 3.3.1 3.3.1 3.3.1 3.3.1 cpu configuration cpu configuration cpu configuration cpu configuration cpu configuration 26 26 26 26 26 processor multiplier this item will show when ?multiplier/voltage change? is set to [manual]; otherwise, it will be hidden. you may set the value from [x4] up to [x25] but no higher than the value of ?processor maximum multiplier?. for example, if the value of ?processor maximum multiplier? is [x11], the actual value of multiplier will be [x11] even if you set this item to a value higher than [x11]. however, for system stability, it is not recommended to adjust the value of this item. processor voltage this item will show when ?multiplier/voltage change? is set to [manual]; otherwise, it will be hidden. you may set the value from [1.550v] down to [0.800v]. however, for safety and system stability, it is not recommended to adjust the value of this item. memory clock this item can be set by the code using [auto]. you can set one of the standard values as listed: [133 mhz (ddr266)], [166 mhz (ddr333)], [200 mhz (ddr400)]. flexibility option the default value of this option is [disabled]. it will allow better tolerance for memory compatibility when it is set to [enabled]. bank interleaving interleaving allows memory accesses to be spread out over banks on the same node, or accross nodes, decreasing access contention. burst length burst length can be set to 8, 4, or 2 beats. bios setup utility cpu configuration if auto, fid/vid will be left at the rated frequency/voltage. if manual, fid/vid will be set based on user selection in setup. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit actual frequency (mhz) cpu host frequency [200] [auto] spread spectrum cool'n'quiet [auto] [disabled] processor maximum multiplier processor maximum voltage processor multiplier processor voltage memory clock flexibility option bank interleaving burst length cas latency (cl) trcd ma timing [x8] [1.500v] [auto] [auto] [4 beats] [auto] [auto] [2t] [disabled] x11 1.550 v multiplier/voltage change [manual] cas latency (cl) use this item to adjust the means of memory accessing. configuration options: [auto], [2.0], [3.0], and [2.5]. 27 27 27 27 27 dram voltage use this to select dram voltage. configuration options are [auto], [high], and [low]. the default value is [auto]. agp voltage use this to select among [normal] and [high] for agp voltage. the default value is [auto]. onboard agp share memory you may select [auto], [8mb], [16mb], [32mb], or [64mb] as the onboard agp share memory. the default value of this feature is set to [auto]. when the total memory is equal or above 256mb, the share memory size will be [64mb]; otherwise, please set the share memory size to [32mb]. primary gra phics adapter this item will switch the pci bus scanning order while searching for video card. it allows you to select the type of primary vga in case of multiple video controllers. agp aperture size it refers to a section of the pci memory address range used for graphics memory. it is recommended to leave this field at the default value unless the installed agp card?s specifications requires other sizes. bios setup utility v02.54 (c) copyright 1985-2003, american megatrends, inc. chipset settings dram voltage agp voltage onboard agp share memory primary graphics adapter agp aperture size agp mode agp fast write ide drive strength pci delay transaction onboard lan onboard ac'97 audio onboard mc'97 modem ht width ht speed [auto] [auto] [auto] [pci] [disabled] [auto] [auto] [64 mb] [auto] [normal] [disabled] [enabled] [auto] [auto] select screen select item + - change option f1 general help f10 save and exit esc exit f9 load defaults to set dram voltage. advanced ma timing use this to adjust values for ma timing. configuration options: [2t], [1t]. the default value is [2t]. 3.3.2 3.3.2 3.3.2 3.3.2 3.3.2 chipset configuration chipset configuration chipset configuration chipset configuration chipset configuration 28 28 28 28 28 agp mode the default value of this feature is set to [auto]. if you install an 8x-agp card on this motherboard, you may select [auto], [8x] or [4x] as the agp mode. if the installed agp card is a 4x-agp card, then you may set the agp mode as [auto], [4x], [2x], or [1x]. agp fast write this allows you to enable or disable the feature of agp fast write protocol support. ide driving strength select [lowest], [low], [normal], or [highest] for ide driving strength. pci delay transaction enable pci delay transaction feature will free the pci bus when the cpu is accessing 8-bit isa cards. disable this feature when using isa cards that are not pci 2.1 compliant. onboard lan this allows you to enable or disable the onboard lan feature. onboard ac?97 audio select [auto], [enabled] or [disabled] for the onboard ac?97 audio feature. onboard mc?97 modem select [auto], [enabled] or [disabled] for the onboard mc?97 modem feature. ht width you may set the hypertransport width as [8 bit], [16 bit] or [auto]. the default value is [auto]. ht speed you may set the hypertransport speed as [auto], [200 mhz], [400 mhz], [600 mhz], or [800 mhz]. the default value is [auto]. 29 29 29 29 29 repost video on str resume this feature allows you to repost video on str resume. it is recommended to enable this feature under microsoft ? windows ? 98 / me. restore on ac/power loss this allows you to set the power state after an unexpected ac/power loss. if [power off] is selected, the ac/power remains off when the power recovers. if [power on] is selected, the ac/power resumes and the system starts to boot up when the power recovers. bios setup utility acpi configuration select auto-detect or disable the str feature. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced suspend to ram restore on ac / power loss ring-in power on pci devices power on ps / 2 keyboard power on rtc alarm power on [disabled] [power off] [disabled] [disabled] [disabled] [disabled] 3.3.3 3.3.3 3.3.3 3.3.3 3.3.3 acpi configuration acpi configuration acpi configuration acpi configuration acpi configuration suspend to ram use this item to select whether to auto-detect or disable the suspend-to- ram feature. select [auto] will enable this feature if the os supports it. if you set this item to [disabled], the function ?repost video on str resume? will be hidden. ring-in power on use this item to enable or disable ring-in signals to turn on the system from the power-soft-off mode. pci devices power on use this item to enable or disable pci devices to turn on the system from the power-soft-off mode. ps/2 keyboard power on use this item to enable or disable ps/2 keyboard to turn on the system from the power-soft-off mode. rtc alarm power on use this item to enable or disable rtc (real time clock) to power on the system. 30 30 30 30 30 3.3.4 3.3.4 3.3.4 3.3.4 3.3.4 ide configuration ide configuration ide configuration ide configuration ide configuration onboard ide controller you may enable either the primary ide channel or the secondary ide channel. or you may enable both the primary and the secondary ide channels by selecting [both]. set to [disabled] will disable the both. configuration options: [disabled], [primary], [secondary], [both]. sata operation mode use this item to adjust sata operation mode. the default value of this option is [raid]. if you don?t want to operate raid function on sata hdds, please select [non-raid]. ide device configuration you may set the ide configuration for the device that you specify. we will use the ?primary ide master? as the example in the following instruction, which can be applied to the configurations of ?primary ide slave?, ?sec- ondary ide master?, and ?secondary ide slave? as well. bios setup utility ide configuration v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced onboard ide controller primary ide master primary ide slave secondary ide master secondary ide slave [both] [hard disk] [not detected] [not detected] [not detected] select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit disabled: disables the integrated ide controller. primary: enables only the primary ide controller. secondary: enables only the secondary ide controller. both: enables both ide controllers. sata operation mode [raid] bios setup utility primary ide master select the type of device connected to the system. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced type lba/large mode block (multi-sector transfer) pio mode dma mode s.m.a.r.t. 32bit data transfer [auto] [auto] [auto] [auto] [auto] [disabled] [disabled] device vendor size lba mode block mode pio mode async dma ultra dma s.m.a.r.t. :hard disk :st340014a :40.0 gb :supported :16sectors :4 :multiword dma-2 :ultra dma-5 :supported 31 31 31 31 31 type use this item to configure the type of the ide device that you specify. configuration options: [not installed], [auto], [cd/dvd], and [armd]. [not installed]: select [not installed] to disable the use of ide device. [auto]: select [auto] to automatically detect the hard disk drive. after selecting the hard disk information into bios, use a disk utility, such as fdisk, to partition and format the new ide hard disk drives. this is necessary so that you can write or read data from the hard disk. make sure to set the partition of the primary ide hard disk drives to active. [cd/dvd]: this is used for ide cd/dvd drives. [armd]: this is used for ide armd (atapi removable media device), such as mo. lba/large mode use this item to select the lba/large mode for a hard disk > 512 mb under dos and windows; for netware and unix user, select [disabled] to disable the lba/large mode. block (multi-sector transfer) the default value of this item is [auto]. if this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. pio mode use this item to set the pio mode to enhance hard disk performance by optimizing the hard disk timing. dma mode dma capability allows the improved transfer-speed and data-integrity for compatible ide devices. s.m.a.r.t. use this item to enable or disable the s.m.a.r.t. (self-monitoring, analysis, and reporting technology) feature. configuration options: [disabled], [auto], [enabled]. 32-bit data transfer use this item to enable 32-bit access to maximize the ide hard disk data transfer rate. 32 32 32 32 32 3.3.5 3.3.5 3.3.5 3.3.5 3.3.5 pcipnp configuration pcipnp configuration pcipnp configuration pcipnp configuration pcipnp configuration pci latency timer the default value is 32. it is recommended to keep the default value unless the installed pci expansion cards? specifications require other settings. pci ide busmaster use this item to enable or disable the pci ide busmaster feature. 3.3.6 3.3.6 3.3.6 3.3.6 3.3.6 floppy configuration floppy configuration floppy configuration floppy configuration floppy configuration in this section, you may configure the type of your floppy drive. bios setup utility pci / pnp configuration value in units of pci clocks for pci device latency timer register. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. pci latency timer pci ide busmaster [32] [enabled] advanced bios setup utility floppy configuration select the type of floppy drive connected to the system. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced floppy a floppy b [1.44 mb 3 "] [disabled] 1 2 33 33 33 33 33 3.3.7 3.3.7 3.3.7 3.3.7 3.3.7 super io configuration super io configuration super io configuration super io configuration super io configuration onboard floppy controller use this item to enable or disable floppy drive controller. serial port address use this item to set the address for the onboard serial port or disable it. configuration options: [disabled], [3f8 / irq4], [2f8 / irq3], [3e8 / irq4], [2e8 / irq3]. infrared port address use this item to set the address for the onboard infrared port or disable it. configuration options: [disabled], [2f8 / irq3], and [2e8 / irq3]. parallel port address use this item to set the address for the onboard parallel port or disable it. configuration options: [disabled], [378], and [278]. parallel port mode use this item to set the operation mode of the parallel port. the default value is [ecp+epp]. if this option is set to [ecp+epp], it will show the epp version in the following item, ?epp version?. configuration options: [normal], [bi-directional], and [ecp+epp]. epp version use this item to set the epp version. configuration options: [1.9] and [1.7]. ecp mode dma channel use this item to set the ecp mode dma channel. configuration options: [dma0], [dma1], and [dma3]. parallel port irq use this item to set the irq for the parallel port. configuration options: [irq5] and [irq7]. bios setup utility configure super io chipset allow bios to enable or disable floppy controller. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced onboard floppy controller serial port address infrared port address parallel port address parallel port mode epp version ecp mode dma channel parallel port irq onboard game port onboard midi port [enabled] [3f8 / irq4] [disabled] [378] [ecp + epp] [1.9] [dma3] [irq7] [enabled] [disabled] 34 34 34 34 34 onboard game port use this item to enable the game port or disable it. onboard midi port use this itme to select the address for the midi port or disable it. configura- tion options: [disabled], [300], and [330]. 3.3.8 3.3.8 3.3.8 3.3.8 3.3.8 usb configuration usb configuration usb configuration usb configuration usb configuration usb controller use this item to enable or disable the use of usb controller. usb 2.0 support use this item to enable or disable the usb 2.0 support. legacy usb support use this item to enable or disable the support to emulate legacy i/o devices such as mouse, keyboard,... etc. or you may select [auto] so that the system will start to auto-detect; if there is no usb device connected, ?auto? option will disable the legacy usb support. bios setup utility usb configuration to enable or disable the onboard usb controllers. select screen select item +- change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. advanced usb controller usb 2.0 support legacy usb support [enabled] [enabled] [disabled] 35 35 35 35 35 3.4 3.4 3.4 3.4 3.4 hardware health event monitoring screen hardware health event monitoring screen hardware health event monitoring screen hardware health event monitoring screen hardware health event monitoring screen in this section, it allows you to monitor the status of the hardware on your system, including the parameters of the cpu temperature, motherboard temperature, cpu fan speed, chassis fan speed, and the critical voltage. 3.5 3.5 3.5 3.5 3.5 boot screen boot screen boot screen boot screen boot screen in this section, it will display the available devices on your system for you to config- ure the boot settings and the boot priority. bios setup utility hardware health event monitoring select screen select item f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. cpu temperature m / b temperature cpu fan speed chassis fan speed vcore + 3.30v + 5.00v + 12.00v : 37c/98f : 2463 rpm :n/a : 1.629v : 3.306v : 5.067v : 11.890v : 31c/87f main advanced boot security exit h/w monitor bios setup utility main advanced h/w monitor security exit boot settings configure settings during system boot. select screen select item enter go to sub screen f1 general help f10 save and exit esc exit v02.54 (c) copyright 1985-2003. american megatrends, inc. boot boot settings configuration hard disk drives removable drives cd / dvd drives 1st boot device 2nd boot device 3rd boot device [1st floppy device] [2nd floppy device] [3rd floppy device] 36 36 36 36 36 3.5.1 3.5.1 3.5.1 3.5.1 3.5.1 boot settings configuration boot settings configuration boot settings configuration boot settings configuration boot settings configuration boot from network use this item to enable or disable the boot from network feature. via sata raid utility use this to enable or disable via vt8237 sata raid bios utility during post. boot up num-lock if this item is set to [on], it will automatically activate the numeric lock function after boot-up. bios setup utility boot settings configuration to enable or disable the boot from network feature. select screen select item + - change option f1 general help f9 load defaults f10 save and exit esc exit v02.54 (c) copyright 1985-2003, american megatrends, inc. boot boot from network via sata raid utility bootup num-lock [disabled] [enabled] [on] 3.6 3.6 3.6 3.6 3.6 security screen security screen security screen security screen security screen in this section, you may set or change the supervisor/user password for the system. for the user password, you may also clear it. bios setup utility main advanced h/w monitor boot exit install or change the password. select screen select item enter change f1 general help f10 save and exit esc exit f9 load defaults v02.54 (c) copyright 1985-2003, american megatrends, inc. security change supervisor password change user password clear user password security settings supervisor password : not installed user password : not installed 37 37 37 37 37 bios setup utility main advanced h/w monitro boot security exit system setup after saving the changes. f10 key can be used for this operation. select screen select item enter go to sub screen f1 general help f10 save and exit esc exit f9 load defaults v02.54 (c) copyright 1985-2003, american megatrends, inc. exit save changes and exit discard changes and exit discard changes load optimal defaults exit options 3.7 3.7 3.7 3.7 3.7 exit screen exit screen exit screen exit screen exit screen save changes and exit when you select this option, it will pop-out the following message, ?save configuration changes and exit setup?? select [ok] to save the changes and exit the bios setup utility. discard changes and exit when you select this option, it will pop-out the following message, ?dis- card changes and exit setup?? select [ok] to exit the bios setup utility without saving any changes. discard changes when you select this option, it will pop-out the following message, ?dis- card changes?? select [ok] to discard all changes. load optimal defaults when you select this option, it will pop-out the following message, ?load optimal defaults?? select [ok] to load the default values for all the setup configurations. 38 38 38 38 38 4. 4. 4. 4. 4. software suppor software suppor software suppor software suppor software suppor t t t t t 4.1 install operating system 4.1 install operating system 4.1 install operating system 4.1 install operating system 4.1 install operating system this motherboard supports various microsoft ? windows ? operating systems: 98 se / me / 2000 / xp. because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. refer to your os documentation for more information. 4.2 support cd information 4.2 support cd information 4.2 support cd information 4.2 support cd information 4.2 support cd information the support cd that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features. 4.2.1 running the support cd 4.2.1 running the support cd 4.2.1 running the support cd 4.2.1 running the support cd 4.2.1 running the support cd to begin using the support cd, insert the cd into your cd-rom drive. the cd automatically displays the main menu if ?autorun? is enabled in your computer. if the main menu did not appear automatically, locate and double click on the file ?assetup.exe? from the bin folder in the support cd to display the menus. 4.2.2 drivers menu 4.2.2 drivers menu 4.2.2 drivers menu 4.2.2 drivers menu 4.2.2 drivers menu the drivers menu shows the available devices drivers including asrock ex- press gbl pci express lan card driver if the system detects the installed devices. please install the necessary drivers to activate the devices. 4.2.3 utilities menu 4.2.3 utilities menu 4.2.3 utilities menu 4.2.3 utilities menu 4.2.3 utilities menu the utilities menu shows the applications software that the motherboard supports. click on a specific item then follow the installation wizard to install it. 4.2.4 4.2.4 4.2.4 4.2.4 4.2.4 contact information contact information contact information contact information contact information if you need to contact asrock or want to know more about asrock, welcome to visit asrock?s website at http://www .a srock.com; or you may contact your dealer for further information. 39 39 39 39 39 appendix: appendix: appendix: appendix: appendix: amd?s cool ?n? quiet amd?s cool ?n? quiet amd?s cool ?n? quiet amd?s cool ?n? quiet amd?s cool ?n? quiet tm tm tm tm tm t t t t t echnology echnology echnology echnology echnology for power-saving sake, it is strongly recommended to enable amd?s cool ?n? quiet tm technology under windows system. when using this feature, please make sure to install ?amd processor driver? from the ?support cd? first. if you are using windows 2000/xp operating system, please follow the instruction below to enable amd?s cool ?n? quiet tm technology: 1. from the windows 2000/xp operating system, click the start button. select settings, then control panel. 2. switch to classic view. (for windows xp only) 3. double-click the display icon in the control panel then select the screen saver tab. 4. click the ?power?? button. the following dialog box appears. 5. from the power schemes combo list box, select minimal power management . 6. click ok to implement settings. if you are using windows 98se/me operating system, please follow the instruction below to enable amd?s cool ?n? quiet tm technology: 1. from the windows 98se/me operating system, click the start button. select settings, then control panel. 2. double-click the display icon in the control panel then select the screen saver tab. 3. from the energy saving features of monitor group, click the ?settings...? button. 4. from the power options properties dialog box, select amd?s cool ?n? quiet tm technology tab. 5. click the performance combo list box, to select desired mode. auto- matic mode is the recommended setting. 6. click ok to implement settings. |
Price & Availability of K8VM800
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |